The much more you use your miter saw, the a lot more dust you’re heading to generate. It’s not just a issue when it arrives to appearance. That dust can clog tools – like resources you are not making use of – and is a health hazard. Let’s encounter it, the dust assortment techniques that appear with most miter saws assortment from becoming basically mediocre to downright terrible. In truth, most toolmakers just tell you to hook your store vac to the back of your observed and take care of it that way.
If you don’t possess a store vac or really don't want the problem of hooking it up whenever you want to use your saw, 1 alternative is to make your possess dust bag. It’s quite straightforward and doesn’t need a lot of supplies.
How to Make a Miter Saw Dust Bag: Guided Steps
1. Gather your materials
The 1st factor you’ll want is a piece of plastic tubing that is large enough to fit the dust vent on the back of your miter noticed. You can either get the measurement from your owner’s handbook, or just select a tube oneself. When you discover a single, try putting it all around the dust vent. You want it comfortable enough that it will not occur free while you are using the observed, but you really don't want it so tight that it’s hard to eliminate when you want to vacant it.
You will also want some sort of bag to spot on the stop of the plastic tubing. The ideal materials are synthetics, because you are filling it with sawdust. The bag ought to be big adequate that it will not fill all the time, but modest enough that it won’t get in the way. Also, appear for one particular with a zipper on it. You are going to want this to vacant the bag after it receives 50 percent complete.
From there, get components to connect the two. We’d recommend a zip tie and industrial-energy glue. You might also want to get a needle and thread.
2. Prepping the plastic tube
There is not any particular duration you need to make the plastic that will link to the dust vent. If you want the dust to get deposited in the bag that’s out of the way, you can make it a tiny more time. Don't forget that it won’t blow out the back again of your noticed with any genuine power, so it is a great idea to maintain it quite quick.
Lower the tube to size, leaving a few of inches at the conclude.
3. Now the bag
Just take the bag and cut the conclude reverse the zipper. Cut it just prolonged sufficient that it’ll fit over the opening of the tube. If you minimize way too significantly, you can use the needle and thread to sew the extra back jointly. You can comply with that up with the industrial-energy glue to preserve the seam sealed shut.
In shape the bag over the back finish of the plastic tube and pull it so that it offers a couple of inches of clearance. This extra area will prevent sawdust from receiving blown into where the bag and tube are linked, which doesn’t just make a mess, but could decrease the operational life of your cobbled-together dust assortment system.
4. Put it all together
Smear industrial-power glue all around in which the bag addresses the plastic tube. It’s a excellent concept if you give this an inch or two for added energy. On the outdoors, you can cinch the two jointly with a zip tie pulled tightly enough to produce a sturdy seal, but not tightly sufficient to crimp the tube. If you managed to hook up the bag and tube by an inch or two, you can use more than one zip tie.
5. Trial run
It’s a good thought to give your dust assortment bag a trial run, so you can proper any deficiencies in your operate before you really give it a great exercise. Minimize some wooden to see how it does at accumulating dust. If the dust is not making it to the bag, try out trimming down the tube a tiny much more. When it receives fifty percent full, empty it by unzipping the finish opposite exactly where the bag covers the tube.
Other ideas
If, following performing this, you choose that a bag just isn’t ample, there are tons of concepts for alternatives. A popular 1 is to develop a dust collection hood to go behind your miter noticed. But, very first, attempt out the bag to see if that’s much better. Easier is generally ideal.
Related: 16 Do-it-yourself Miter Observed Initiatives to Try out Today
Sources:
https://www.youtube.com/view?v=iKj-g-Z81gk
https://www.youtube.com/view?v=7tkKrkBRieU
https://www.doityourself.com/stry/how-to-create-and-attach-a-dust-bag-for-your-miter-saw
https://www.doityourself.com/stry/3-techniques-to-enhance-the-dust-bag-on-your-miter-saw
https://www.thehandymansdaughter.com/miter-noticed-dust-collection/
https://www.oneprojectcloser.com/how-to-make-compound-miter-observed-dust-hood/
Featured Picture Credit history: maksimee, Shutterstock
Contents
