How to Replace Garage Door Rollers in 12 Steps (with Pictures)

Replacing the rollers on a garage door is frequently a easy Diy venture. If you’ve never accomplished it before, it can consider a little bit of getting utilized to, but by the time you have replaced the 10—12 rollers that most garage doorways have, you will be a professional!

If you have a helper, it will make this process safer and simpler. Nonetheless, it can nevertheless be done securely by operating very carefully, not speeding, and using a strong stepladder to replace leading rollers.

Before you start, here is a list of tools and supplies to make sure you have:
  • Safety: Safety glasses, work gloves,
  • Tools: Pliers, hammer, screwdrivers, step ladder, clamp
  • Supplies: New rollers
How to Replace Garage Door Rollers in 12 Steps (with Pictures)
Image Credit: Bru-nO, Pixabay

How to Replace Garage Door Rollers (12 Steps)

1. Open the Garage Door

Changing rollers from the bottom to the top is the easiest and most secure way to comprehensive this task. Whether or not manually or with your computerized opener, make positive the door is in its totally open placement.

Also, donning safety glasses and perform gloves is advised from here on out.


2. Make Sure the Power is Off

If your garage doorway is geared up with a electricity opener, disconnect the door from the opener. Typically, this is accomplished by pulling a rope connected to the arm which is activated by the opener motor.

For extra safety, physically disconnect the electrical power opener by unplugging it from its electrical power resource. If it’s wired immediately to the electrical power supply, pull the fuse or flip the breaker.

This additional action helps prevent the doorway from activating unsafely if the arm accountable for the automatic operation was at any time bumped back again into area.


3. Pry Open a Space in the Track

Make a decision which aspect of the door you want to commence with and established up a small desk to keep your equipment inside of attain. This will make your daily life less difficult if you don’t have a helper.

Discover the seam in the keep track of. It will be in which the vertical piece fulfills the curved portion that goes to the ceiling. Using pliers or the claw of a hammer, bend the seam open. You are going to want to bend approximately 1-2 inches of track open.

How to Replace Garage Door Rollers in 12 Steps (with Pictures)
Image Credit: oneSHUTTER oneMEMORY, Shutterstock

4. Pop the Old Roller Out of the Track

Little by little pull the door down so that the bottom roller is lined up with the opening in the track. With 1 hand, maintain the doorway continual and pop the roller out from the lip with the other hand. When launched, it will come out of the observe.

Preserve the doorway steady, as that element of it will now be unfastened without the roller in the observe.

At this stage, you need to be capable to get the old roller out of the bracket. Sometimes, you may need to tap it a minor bit with a hammer if it’s twisted or normally ruined.


5. Put in the New Roller

If the bracket the place the roller goes is twisted, it can often be straightened with pliers at this level. This will make sliding the new roller in significantly simpler.

As soon as you are content with the bracket, place the new roller in and pop it again into the keep track of. If it does not go in very easily, sometimes you can gently pry it in with your screwdriver—but be mindful not to bend the new roller.


6. Continue Replacing All Rollers EXCEPT the Top One

Repeat measures four and five right up until you reach the last top roller. It might be tempting to reduce the door and pop all the rollers out at once, but this will make the entire activity much much more complex and could end result in critical harm if the door falls on you.

Also, DO NOT do the previous roller. After you have finished equally sides of the garage, you will do the leading roller on each and every side.

How to Replace Garage Door Rollers in 12 Steps (with Pictures)
Image Credit: JayMantri, Pixabay

7. Bend Track Closed

As soon as you have carried out all rollers on 1 side, bend the monitor back again to how it was. Make positive that you get the seams flush with every other or else, your rollers could catch. This could perhaps result in harm to the opening program.


8. Repeats steps for the Other Side

Reopen the garage doorway, and repeat methods two by means of seven once more.


9. Support the Door

With the door open, put a clamp approximately 1 foot from the ground. This prevents the door from closing while you’re changing the top roller.

If you really don't have a clamp, any sturdy object that is around one foot higher will suffice.


10. Pop Top Roller Out of Track and Replace with New One

Carefully reduce the door down to where you have your stop in area. Give it a minor thrust to guarantee it is protected simply because you do not want it to occur down although you are on the ladder changing the roller.

After you are relaxed on your ladder, pry the old roller out a lot the very same way you did the bottom rollers. Simply because the top part of the keep track of is a lot more adaptable, you can usually pry the roller out without having bending the observe.

Exact same as ahead of, make sure the bracket the roller comes out of is in very good shape and then slide the new roller in.

Notice: After you pop the previous roller out, the prime panel of the door will be free. Make certain you are ready for it, so you are not knocked from your ladder.


11. Secure New Roller in Track

Due to the fact of the track’s flexibility, you ought to be able to twist it just sufficient that you can pop the new roller into its seat. If you simply cannot twist it sufficient, then pry open up the monitor just like before—don’t fail to remember to bend it again when the roller is in.


12. Repeat Steps for the Other Side

Repeat steps 9 by means of eleven for the 2nd best roller.

After equally rollers are changed, cleanse all equipment and supplies absent from the garage door path. Reconnect the opening arm to the automated opener. Plug in the motor or flip the breaker to power up the opener.

Examination the door to make certain your keep track of was bent back properly and the door opens and closes effortlessly.

Conclusion

After you have altered these rollers, you actually should not have to do it yet again for yet another twelve – fifteen several years as long as you replaced them with substantial-top quality replacements. Also, most producers advise lubricating the hinges and rollers every six months. This makes certain they remain working in idea-best form for as extended as feasible.


Featured Picture Credit: Radovan1, Shutterstock

Contents