It just doesn’t seem right when a flooring goes from carpet to concrete, laminate to concrete, or just about anything to concrete — that is, if you really do not use a changeover strip.
These basic minor gadgets develop a seamless changeover from concrete to just about any other flooring surface area, and they are simple to set up! We adore changeover strips, and that’s why we developed this manual to walk you by means of every little thing that you need to know to install them.
What You’ll Need
Practically nothing is a lot more annoying than receiving midway via a task only to realize that you want to get a lot more provides. Which is why we want to spotlight all the tools and components that you are going to need to finish the work proper right here.
You don’t need much, which is excellent information for those who are new to the Do it yourself globe or basically really don't have many resources of their possess. If you do not want to commit in the hammer drill, you can usually hire 1 out from a keep like Residence Depot or Lowe’s.
How to Install a Transition Strip on Concrete in 6 Simple Steps
Now that you have almost everything you need to have, it is time to get started out. The good news is that you ought to be ready to set up your new transition strip in much less than 30 minutes!
1. Measure Everything
The final issue that you want to do is get the transition strip down, only to realize that it is possibly as well modest or too massive. You ought to start off each and every project by measuring the location where you want to put in it. Figure out how lengthy you want the strip to be, then get a strip that is at minimum that extended.
Measure out the strip to the appropriate length, and mark it just before transferring on to the up coming action.
2. Cut the Transition Strip to Size
Transfer the transition strip to your miter noticed, and reduce it down to the mark that you made. Make sure that the blade you are employing on your miter observed can minimize steel, but preserve in mind that transition strips are really skinny, so you really do not need a cumbersome miter saw blade.
3. Mark Out the Holes
Lay down your transition strip in which you want to put it, then use your everlasting marker to mark out the holes in which you need to have to put in the concrete screws. As soon as you complete marking out the holes, go the transition strip out of the way and go to the up coming action.
4. Drill the Holes
To install the changeover strip, you want to drill out where you marked. Use your five/32” drill little bit, and drill about 1.5” down with your hammer drill. Get your time with this action and attempt to drill straight down.
5. Vacuum the Mess
After you complete drilling the holes, you need to clear up the mess that it tends to make. If you skip this phase, you’ll have to offer with concrete dust escaping from underneath the transition strip. You also may well battle to install the concrete screws if there’s too much dust within the gap.
6. Install the Concrete Screws
The very last phase is to screw in your three/16” concrete screws. You need to be ready to do this with a screwdriver, but it may well be less complicated if you have a drill. Entirely set up every single concrete screw to give it a flush look.
Frequently Asked Questions
There is a lot of info out there about putting in transition strips on concrete, and some of it is contradictory. That is why we made a decision to response a handful of often asked concerns below.
Can I Glue Transition Strips to Concrete?
Whilst you can glue changeover strips to concrete, it doesn’t give the same toughness and quality of results as drilling it down. No make a difference what kind of glue you use, in excess of time, it’ll begin to put on down, and the changeover strip will commence to increase.
That’s why we always recommend drilling a transition strip into spot when you can. You are going to get more time-lasting outcomes, and it’s not that tough to do.
When Should You Avoid Drilling for a Transition Strip?
While we desire drilling when putting in a changeover strip, there are a few circumstances where you are going to want to glue it down alternatively. The very first is if you have a flooring which is still beneath warranty. This could be because it’s a new house or you recently contracted out the installation of the flooring.
If you drill into a floor that has a guarantee, there is a great opportunity that you may void the guarantee. Gluing down a changeover strip normally does not have this exact same danger.
The next predicament the place you might want to glue the strip down instead of drilling it in is if the concrete flooring isn’t thick. Although a appropriately set up concrete ground need to be everywhere from four to 6 inches thick, not each concrete flooring will be.
If which is the case with your flooring, think about gluing down the transition strip since the concrete screws will not have enough to hold onto normally.
What Is the Best Adhesive for Concrete?
If you do have to use an adhesive to connect your transition strip instead of screws, you require to use the right adhesive to give you the very best possible final results. Use a concrete-strength adhesive like Loctite Excessive Glue Gel or Gorilla Weighty Obligation Development Adhesive to get the occupation carried out.
These adhesives should hold for several years if you apply them appropriately and really don't get a ton of targeted traffic over the changeover strip.
Final Thoughts
Changeover strips might not appear like a large deal, but they do a phenomenal work of giving your place a excellent look and can even help avert stubbed toes! Thinking about how easy they can be to put in and how inexpensive they are, it’s a great novice Diy project for your property or enterprise!
Featured Picture Credit: Only NewPhoto, Shutterstock
Contents
